Clecoed Bottom Skins and Leading Edge on Right Wing

Prev | Next

Oh man, what a great day!!

After some good advice to stop worrying about the wing twist too much (“you’ve got a pre-punched kit, it’ll work out”), I got started on some of the next tasks on the right wing. First, I clecoed on the right top skins, and then grabbed the right leading edge and sat it on the main spar.

Looks like a wing!

Oh wait. One of the next steps is to trace some lines on the lower skins (forgot those) that intersect at the tiedown hole so I can transfer those lines to the leading edge so I can verify that the leading edge prepunched hole for the tiedown is correct. I haven’t attached the tiedowns yet, so I went searching for the hardware.

Apparently you need an AN3-7A bolt, a couple AN960-10 (and L) washers, and an AN365-1032 nut.

I couldn’t figure out which washer (skinny or fat) goes on which side of the spar, so I looked at the tiedown area of one of the drawings (can’t remember which one.)

First, though, I have to finally sort out which washer …-10 or …-10L is the skinny one. Turns out, I should remember that “L” means “lean” (not really, but that’s how I’ll remember it.

AN960 Flat Washers
Bolt Size OD Thickness Part No.
#10 0.438″ 0.063″ AN960-10
#10 0.437″ 0.032″ AN960-10L

Anyway, I hope that having looked that up now, I’ll remember which is which.

Okay. Looks like the -10L washers go on the bolt head side of the AN3-7A bolts.

Then, I realized that I don’t really need to tighten these things up. I’ve got some work to do in the future on the bellcrank brackets and bushings, etc., so I really just need to set these in place.

After putting the four bolts through the tiedown and clecoing on the bottom skins, I've got this.

Next, they want you to draw a few lines on the bottom skin that intersect at the tiedown hole.

You can just barely see my lines on either side of the access hole.

Next, I slapped the leading edge into place (but first had to notch my angles…bummer).

I only had to notch very slightly. Still very annoying to me.

After starting (pronounced “attempting”) to cleco on the leading edge, I realized I am going to need some mechanical advantage to snug everything up so I don’t have to use the clecos to pry things into place (a big no-no).

I got out a few 2x4 scraps and placed them against the rear spar. (This is so the straps don't put any pressure on the aft end of the skins.)

Strapped! (Not very much, just enough to act as a third hand while clecoing.)

After a good  30 minutes of the most difficult clecoing on the project, I had the leading edge nice and secured to the right wing.

Notice the amount (lots) of clecos on the aft part of the leading edge.

I think this is just a picture of the bottom side of the right wing.

Then, I extended my lines back onto the leading edge.

The intersection of the lines is sooooooo close.

I didn’t really believe I was off a little (although this is normal), so I grabbed this picture from the inside. (Depending on how precisely you place the tiedowns when you measure and drill them to the spars, you’re hole may be off here.)

That little tiny light is so close to the center of the tiedown hole, I'm going to start there, and file a little bit in one direction if I have to adjust.

Anyway, I decided I don’t want to start on drilling the skins to the skeleton until I do some more clecoing. I’m going to break down and just order like 400 more clecos before drilling. It can’t hurt to cleco every other hole (Van’s suggests every 4th hole before drilling)…things will only be lined up better, and since I’m already worried about twist, this will help me sleep at night.

A quick survey of tool joints yields the following for 3/32″ spring cleco prices.

3/32″ Spring Cleco Prices
Source Price per Cleco
Aircraft Spruce $0.43, plus shipping
Avery Tools $0.42, free shipping >$95
Brown Tools $0.44, 0.42 if >100, free shipping >$95
Cleveland Tools Website is not working…
Vans Aircraft $0.40, plus shipping
The Yard Store $0.40, free shipping >$100.
PlaneTools.com $0.79…WHAT?!!
Aircraft Tool Supply $0.49, plus shipping.
Innovative Tooling Services $0.35, free shipping >$100

UPDATE: Just found Innovative Tooling. The picture on the page for 3/32″ doesn’t show a silver cleco, but I’m assuming they just used the same picture. Just placed my order, we’ll see how they are when they arrive.

OLD: Looks like the yard store wins…they used to have bulk used clecos in 3/32″ size, but I called today and they are out. I’ll have to order new clecos, but bummer they are still $0.40 each. (By the way, who gets off selling clecos for $0.79 each?)

Anyway, I”ll order some tomorrow. One last picture of the WING! that’s in my garage tonight.

This makes me happy.

1.5 GLORIOUS, PRODUCTIVE hours. Night’s like tonight make all the other crappy nights worth it.

Prev | Next

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: