Advertisements
 

Deburred Right Upper Outboard Wing Skin, Right Leading Edge Rivets

Prev | Next

Tonight was only mildly more exciting than last night!

After taking the right upper outboard skin inside to deburr and scuff (AND VACUUM THE LITTLE ALUMINUM SHAVINGS OFF THE COUNTER, SORRY GIRLFRIEND!!!), I brought it back outside, and stored it (like the inboard skin), upside down (or inside out) on the left wing.

The two upper right wing skins, stored on the left wing for now.

For some reason I am paranoid about alignment, so I clecoed the right lower skins in place, although only 25%. I’ll come back with more clecos when I start riveting to make sure things are perfect.

The lower side of the right wing.

After looking at the clock, I figured I had about 30 more minutes.

Time to look at getting the right leading edge riveted to the spar (I had done the skin rivets, albeit out of order, a few days ago.)

From Brad Oliver’s site:

Oh boy, what a night. I riveted the left leading edge to the spar tonight. I used blind rivets to do this job, MSP-42, -43 and -44 rivets from Aircraft Spruce to be exact, but that isn’t the end of the controversy. I riveted (pulled) these rivets from inside the leading edge. Why use blind rivets? Why from the inside? Well, first of all, in my opinion certain blind rivets blind rivets are completely acceptable here. Van’s has said to many builders that the use of LP4-x rivets is acceptable here, and the LP4s are pretty soft as rivets go. I decided to step it up a bit and use MSP rivets here. They have a Monel (M) head, with a steel shaft (S), and a protruding head (P), and by my calculations are very similar in strength to solid rivets. I am likely to catch flack for that statement, but do your own calculations and see for yourself. Don’t take my word for it, and I am not recommending this method, only documenting what I did.

Why use blind rivets here in the first place? Because riveting the LE ribs to the spar involves grinding down a rivet set and you need two people for the job. These certainly aren’t big issues, but I wanted a easy method I could do myself.

Why from the inside? That one is easy, I wanted the factory head of the rivet to be on the thinner material (aft flange of rib). This was slightly painful, but I am proof that it can done. I also did this because even with the face of my cheap-o rivet puller ground down, I was having a hard time getting the puller on the shaft of the rivets due to their close proximity to the aft rib webs.

From Mike Bullock’s site:

No way to squeeze them. You could buck and shoot them, but you have basically no room to get a rivet set onto these rivets with the rib interference. The only purpose for these rivets are to keep the spar from bluckling. The way I see it, the chance of that is NIL, and there is a main rib set right next to each leading edge rib with the proper rivets in it. It doesn’t say it in the instructions, but builders have been told by Van’s to use LP4-3 blind rivets here. I did one better and used Cherry MSP-4? rivets. I bought a bunch of them from Spruce in the MSP-42, 43 and 44 sizes. They are very comperable to solid rivets.

I had some MSP-42 rivets in stock, so I grabbed 5 of them to try it out.

Once I got the ribs pulled into alignment, it worked great.

See? Great.

And any day you weren’t planning on contributing to your rivet total but you do…it’s a good day.

1.0 hour. 5 rivets. I’ll do the rest of the leading edge tomorrow. Also, someone PLEASE remind me to buy a balloon and a bicycle tire pump to test this darn right tank. It’s been two weeks, so the pro-seal better be dry.

Prev | Next

Advertisements

One Response to Deburred Right Upper Outboard Wing Skin, Right Leading Edge Rivets

  1. MOM says:

    Hey Andrew, remember to go get the stuff, bicycle pump, etc. To test the tank. That stuff is dry enough now!

    MOM

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: